﻿ Fine Aggregate Calculation

## Fine Aggregate Calculation ### Example Calculation of FM of Fine Aggregate

2019-10-23  Example Calculation of FM of Fine Aggregate Order by Phone: 800.444.1508 / 740.548.7298 • Order Online: globalgilson Test Sieve Sieve Opening Mass Retained, Grams Cumulative Mass Retained Cumulative Percent Retained No. 4 4.75mm 31.5 31.5 6.3 No. 8 2.36mm 67.6 99.1 19.8 No. 16 1.18mm 96.5 195.6 39.1 No. 30 600μm 111.1 306.7 61.3

More ### [PDF] CALCULATION OF THE CLOSE PACKING OF FINE

The paper considers the calculation of the maximum packing density of fine aggregate. The selection of the granulometric composition of the aggregate is given. The bulk densities and packing densities of standard screening fractions were determined. The content of each fraction in the mixture and the packing density of the aggregate mixture are calculated by the introduction of a subsequent ...

More ### METHOD OF CALCULATION OF THE FINENESS

4. Example For this procedure 4.1 A typical example of the calculation of the fineness modulus is shown below: Fineness N (100) - Sum Total of Percent Passing Total Percent Retained Modulus 100 Fine Coarse Combined Sieve Sizes, Aggre- Aggre- Course and where U. S. Series gate gate Fine 65:35 N = number of sieves involved in the sum total of ...

More ### Mathematical Model of Fine Aggregate Granulometry ...

2017-4-22  function of the coarse aggregate. For the case of the fine aggregate, the size d smaller than 4.76 mm will have a n of 0.305 𝐏= 𝐝 𝐃 𝐧 ( ) In practice, it was observed that increasing the value of n causes that more compaction energy is needed to achieve a unit MAS and a maximum resistance.

More ### FINENESS MODULUS OF FINE AGGREGATE

2014-9-29  FINENESS MODULUS OF FINE AGGREGATE TXDOT DESIGNATION: TEX-402-A CONSTRUCTION DIVISION 1 – 2 LAST REVIEWED: SEPTEMBER 2014 Test Procedure for FINENESS MODULUS OF FINE AGGREGATE TxDOT Designation: Tex-402-A Effective Date: August 1999 1. SCOPE 1.1 This method determines the fineness modulus of concrete fine aggregate used in

More ### Determination of Specific Gravity of Fine Aggregates -

🕑 Reading time: 1 minuteSpecific gravity of fine aggregate (sand) is the ratio of the weight of given volume of aggregates to the weight of equal volume of water. The specific gravity of sands is considered to be around 2.65. Contents:Apparatus for Specific Gravity TestProcedure of TestCalculationsQuestion : Apparatus for Specific Gravity Test A balance []

More ### SPECIFIC GRAVITY AND ABSORPTION OF FINE

2014-4-14  Lightly tamp the fine aggregate into the mold with 25 light drops of the tamper (Figure 3). Each drop should start about 1/5 in. above the top surface of the fine aggregate. Remove loose sand from base and carefully lift the mold vertically. If surface moisture is still present, the fine aggregate will retain the molded shape. When the sand ...

More ### How to Calculate Cement Sand and Aggregate

2021-7-23  Dry aggregate contains 33 to 34% air voids, whereas sand contains 20% air voids and cement contains very fine particles hence it contains negligible are voids so we can ignore it. Now add the air voids of sand and aggregate that are 20% +34% = 54% so this is the reason we have to add 54% for wet to dry volume of materials.

More ### How to Calculate Cement, Sand and Coarse Aggregate ...

2021-7-21  Concrete Ingredients Calculation. For Cement, Sand and Coarse Aggregate. This is a Volumetric Calculation. Assuming we need 2 m 3 of concrete for M20 Concrete Mix, (Mix Ratio, M20 = 1 : 1.5 : 3) Total Part of the Concrete = 1+1.5+3 = 5.5 Parts.

More 2020-1-21  Open-Graded Aggregate Decent range of sizes Very few fine particles Grain-to-grain contact High void content High permeability High stability Difficult to compact. CIVL 3137 19 Gap-Graded Aggregate 0 20 40 60 80 100 100 10 1 0.1 0.01 Percent Passing Opening Size (mm) 1½" ¾" 3/ 8" 4 8 16 30 50 100 200 Open graded gravel Open graded sand Gap graded

More ### Sieve Analysis of Coarse and Fine Aggregates

2020-8-31  Larger value of FM is preferred for fine aggregates. For a good fine aggregate, the FM should be between 2.3 and 3.1 (ASTM Range for fine aggregates). A FM of 4 can be interpreted to means that the fourth sieve from bottom i.e. sieve No. 16 is the average size of the aggregate particles in the given sample.

More ### Calculate Cement Sand Aggregate - M20, M15,

The ratio of fine to coarse aggregate is chosen as usual as 1:2. From the above table we know we need 250kg of total dry aggregate for our concrete. The general ratio of fine aggregate to coarse aggregate is 1:2, but it can be adjusted between 1:1.5 to 1:2.5 based on the grading of fine aggregate and size of coarse aggregate. Sand = 1 Part

More ### Concrete Mix Design Calculation For M35 Grade

2021-7-28  Calculation of Coarse and Fine Aggregate Content; Volume of Coarse aggregate corresponding to 20mm size aggregate and fine aggregate Grading Zone IV, for water cement ratio is found out to be 0.66. But in present case we are considering W / C ratio as 0.38. Here, 0.5 – 0.38 = 0.12. Therefore it is less by 0.12.

More ### How To Calculate Cement, Sand And Coarse

2 天前  Volume of Coarse Aggregate = 3/5.5 x 1.55. So the required Cement Volume – 0.282 m 3 or 8.14 Bags Sand Volume – 0.423 m 3. Coarse Aggregate – 0.845 m 3. Water Cement Ratio Calculation. From the IS Code standard, Assuming the water-cement ratio for M20 is 0.55. Therefore required water quantity = Cement Volume X WC Ratio = 0.282 X 0.55 = 0 ...

More ### METHOD OF CALCULATION OF THE FINENESS

4. Example For this procedure 4.1 A typical example of the calculation of the fineness modulus is shown below: Fineness N (100) - Sum Total of Percent Passing Total Percent Retained Modulus 100 Fine Coarse Combined Sieve Sizes, Aggre- Aggre- Course and where U. S. Series gate gate Fine 65:35 N = number of sieves involved in the sum total of ...

More ### Determination of Specific Gravity of Fine Aggregates -

🕑 Reading time: 1 minuteSpecific gravity of fine aggregate (sand) is the ratio of the weight of given volume of aggregates to the weight of equal volume of water. The specific gravity of sands is considered to be around 2.65. Contents:Apparatus for Specific Gravity TestProcedure of TestCalculationsQuestion : Apparatus for Specific Gravity Test A balance []

More ### Calculate Cement Sand Aggregate - M20, M15,

The ratio of fine to coarse aggregate is chosen as usual as 1:2. From the above table we know we need 250kg of total dry aggregate for our concrete. The general ratio of fine aggregate to coarse aggregate is 1:2, but it can be adjusted between 1:1.5 to 1:2.5 based on the grading of fine aggregate and size of coarse aggregate. Sand = 1 Part

More ### DETERMINING UNIT MASS (WEIGHT) OF AGGREGATES

2016-7-8  4.1.2 Fine Aggregate: 4.1.2.1 The fine aggregate sample should be large enough (after drying) to fill the 0.003 m3 (0.1 3ft. ) measure to overflowing. Use a small scoop to place the sample of sand into the denim sleeve. 4.1.2.2 Place the 0.003 m3 (0.1 ft.3) measure in a large flat pan so that excess material may be recovered for check tests.

More ### Fineness Modulus Of Sand Sieve Analysis Of Fine ...

2020-12-15  Sieve Analysis of Fine Aggregate. Following is the test procedure for fineness modulus of sand test, 1) Take the sieves and arrange them in descending order with the largest sieve on top.. 2) If a mechanical shaker is using for shaking, then put the sieve set in position on the mechanical shaker and pour the sample in the top sieve then close it with the sieve plate.

More ### How to Calculate Cement, Sand and Coarse Aggregate ...

2021-7-21  Concrete Ingredients Calculation. For Cement, Sand and Coarse Aggregate. This is a Volumetric Calculation. Assuming we need 2 m 3 of concrete for M20 Concrete Mix, (Mix Ratio, M20 = 1 : 1.5 : 3) Total Part of the Concrete = 1+1.5+3 = 5.5 Parts.

More ### Concrete Material Calculation / Concrete Quantity

2 天前  Here, 1 is a Cement, 2 is a Fine Aggregate, 4 is a Course Aggregate. Dry Volume of concrete = Wet Volume of Concrete X 55 % (Because of working time Dry Volume less as per using qty so, we need 30% and 25 % of wastage qty, Here 30% + 25% = 55% access of this qty) Sum propositions Ratio (sa) =

More ### How To Calculate Cement, Sand, Aggregate

2018-8-3  CALCULATION FOR AGGREGATE QUANTITY. Consider volume of concrete = 1m3. Dry Volume of Concrete = 1 x 1.54 = 1.54 m3. Aggregate = (3/5.5) x 1.54 = 0.84 m3 ∴ 3 is a part of cement, 5.5 is sum of ratio. Density of Aggregate is 1500/m3. Calculation for KG = 0.84 x 1500 = 1260 kg. As we know that 1 m3 = 35.31 CFT.

More ### How To Calculate Cement, Sand And Coarse

2 天前  Volume of Coarse Aggregate = 3/5.5 x 1.55. So the required Cement Volume – 0.282 m 3 or 8.14 Bags Sand Volume – 0.423 m 3. Coarse Aggregate – 0.845 m 3. Water Cement Ratio Calculation. From the IS Code standard, Assuming the water-cement ratio for M20 is 0.55. Therefore required water quantity = Cement Volume X WC Ratio = 0.282 X 0.55 = 0 ...

More 2020-1-21  Open-Graded Aggregate Decent range of sizes Very few fine particles Grain-to-grain contact High void content High permeability High stability Difficult to compact. CIVL 3137 19 Gap-Graded Aggregate 0 20 40 60 80 100 100 10 1 0.1 0.01 Percent Passing Opening Size (mm) 1½" ¾" 3/ 8" 4 8 16 30 50 100 200 Open graded gravel Open graded sand Gap graded

More ### Sieve Analysis Test Procedure And Calculation

2021-7-25  Sieve Analysis Test Procedure and Calculation. The aggregates are graded as fine and coarse aggregate based on the grain size. When the aggregate size is greater than 4.75mm is called coarse aggregate, and less than 4.75mm is called fine aggregate. The sieve analysis test

More ### Fineness Modulus of Fine Aggregate Fineness

2021-7-23  Fineness Modulus of Fine Aggregate: The sand fineness module (fine aggregate) is an index number describing the mean size of sand particles. By doing sieve analysis with normal sieves, it is measured.. The accumulated percentage kept on each sieve is applied and the sum of the fine aggregate is subdivided by 100. To find the fine aggregate

More ### TOTAL MOISTURE CONTENT OF AGGREGATE BY DRYING

2014-4-14  The aggregate sample shall be obtained in accordance with AASHTO T 2 and protected against loss of moisture prior to determining the weight. An air-tight container or plastic bag is best for ... The calculation for moisture content (P) is as follows: P = 100 (W -

More ### Fineness Modulus of Fine Aggregate

Fine aggregate (sand) grading affects consistence and finishability. Fineness Modulus (FM) is an empirical calculation used to support the optimisation of a concrete mix design. It is used to determine ‘degree of uniformity of the grading’. This can create a relationship between grading and consistence and/or the amount of cement or water ...

More ### Fineness Modulus of Fine Aggregate Fineness

2021-7-23  Fineness Modulus of Fine Aggregate: The sand fineness module (fine aggregate) is an index number describing the mean size of sand particles. By doing sieve analysis with normal sieves, it is measured.. The accumulated percentage kept on each sieve is applied and the sum of the fine aggregate is subdivided by 100. To find the fine aggregate

More ### Fineness Modulus of Fine Aggregate

Fine aggregate (sand) grading affects consistence and finishability. Fineness Modulus (FM) is an empirical calculation used to support the optimisation of a concrete mix design. It is used to determine ‘degree of uniformity of the grading’. This can create a relationship between grading and consistence and/or the amount of cement or water ...

More ### Fine Aggregate Specific Gravity – Pavement Interactive

For a particular aggregate type or source, fine aggregate specific gravities can be slightly higher than coarse aggregate specific gravities because as the aggregate particles get smaller, the fraction of pores exposed to the aggregate surface (and thus excluded from the specific gravity calculation because they are water-permeable) increases.

More ### DETERMINING UNIT MASS (WEIGHT) OF AGGREGATES

2016-7-8  4.1.2 Fine Aggregate: 4.1.2.1 The fine aggregate sample should be large enough (after drying) to fill the 0.003 m3 (0.1 3ft. ) measure to overflowing. Use a small scoop to place the sample of sand into the denim sleeve. 4.1.2.2 Place the 0.003 m3 (0.1 ft.3) measure in a large flat pan so that excess material may be recovered for check tests.

More ### How to Calculate Cement, Sand and Aggregate

2021-7-25  2.Fine Aggregate = 115/0.167 = 689 kg. 3.Coarse Aggregate = 209/0.167 = 1252 kg. 4.Water = 300/0.55 = 165 kg. Like wise other concrete mix with varying proportions and materials with different physical properties ,the individual quantities of

More ### Concrete Material Calculation / Concrete Quantity

2 天前  Here, 1 is a Cement, 2 is a Fine Aggregate, 4 is a Course Aggregate. Dry Volume of concrete = Wet Volume of Concrete X 55 % (Because of working time Dry Volume less as per using qty so, we need 30% and 25 % of wastage qty, Here 30% + 25% = 55% access of this qty) Sum propositions Ratio (sa) =

More ### What is bulk density and % of voids of fine aggregates ...

2021-7-24  And percentage of voids present in fine aggregate is calculated with the help of specific gravity of fine aggregate and their Loose bulk density by the following formula. % of voids = { (Gs _R)/Gs}×100. Where Gs = specific gravity of fine aggregate and their value is 2.62. R = loose bulk density of fine aggregate = 1.398 kg/L.

More ### Utilization of Stone Dust as Fine Aggregate Replacement

2015-4-30  coarse aggregate I. INTRODUCTION – Concrete is commonly used construction material due to its ease of availability, mouldable, rigidity and durability. It consists of binding material, fine aggregate, coarse aggregate and required quantity of water, where sand is normally used as fine aggregate.

More ### How To Calculate Cement, Sand And Coarse

2 天前  Volume of Coarse Aggregate = 3/5.5 x 1.55. So the required Cement Volume – 0.282 m 3 or 8.14 Bags Sand Volume – 0.423 m 3. Coarse Aggregate – 0.845 m 3. Water Cement Ratio Calculation. From the IS Code standard, Assuming the water-cement ratio for M20 is 0.55. Therefore required water quantity = Cement Volume X WC Ratio = 0.282 X 0.55 = 0 ...

More ### Sieve Analysis Test Procedure And Calculation

2021-7-25  Sieve Analysis Test Procedure and Calculation. The aggregates are graded as fine and coarse aggregate based on the grain size. When the aggregate size is greater than 4.75mm is called coarse aggregate, and less than 4.75mm is called fine aggregate. The sieve analysis test

More ### Calculation of Quantity of material for RCC cement

2020-4-24  Calculation of Quantity of material for RCC cement sand aggregate To download excel file scroll down and click download ... Volume of fine aggregate Required = (1.5/5.5) x 1.55 = 0.422 m3. Volume of cement = (1/5.5) x 1.55 = 0.281 m3 = 0.281 x1440 = 405kg . For 1m3 of M20 (1:1.5:3) ...

More ### Calculation the quantities of Cement, Sand and

2020-5-6  Calculation the quantities of Cement, Sand and Aggregate. Calculation the quantities of cement, sand and aggregate are most important in estimating work and costing of the building . Aggregate shall be of invert materials and should be clean, dense, hard, sound, durable, non absorbent and capable of developing good bond with mortar.

More ### (PDF) Sieve Analysis and Gradation of Coarse and Fine ...

STONE - 2.7 1600 1.5% -. Stone Aggregate Brick Aggregate. 4. Aggregate. Fine aggregates shall be angular (gritty to touch), hard and durable, free from clay, mica and soft. flaky pieces. Sand is a ...

More ### Excel Sheet For Sieve Analysis Of Aggregate And To ...

The sieve analysis, commonly known as the gradation test, is a basic essential test for all aggregate technicians. The sieve analysis determines the gradation (the distribution of aggregate particles, by size, within a given sample) in order to determine compliance with design, production control requirements, and verification specifications.

More